for more information please call +971 4 337 1230 or mail to sealmech@eim.ae
 
 
 

Gland Packing Tools

 

 

AA-100 Packing Extraction Hooks.These tools are designed to assist in the removal of packing rings from the stuffing box.   They are ideal for packing that has become hard, burned or flaky.   These hooks work well where standard screw packing extractors tend to only want to pull out small pieces of packing

Back to top >


AA-200 Packing Tamping Tools. For the best results when packing a stuffing box, each packing ring should be tamped firmly into place to insure a seal to the shaft and the walls of the stuffing box.   These tools are designed to help you accomplish this.   The Tamping Tools are made from flexible high strength material

Back to top >


AA-300 Hose cutter Largest cutter - cuts hose through 2" I.D., P.E. through 1-1/2" & Class PVC through 1-1/4" I.D. (Comes standard with Stainless Steel Blade)

Back to top >


AA-400 Gland Packing extractor

The Packing Extractor is designed to facilitate the removal of old packing of any size from 3/16” upward. This can be a difficult and tiresome procedure made simple and quick by the use of the Packing extractor. The long flexible shank of the Packing Extractor makes access easy even to those glands in the most awkward positions. The hardened and tempered steel screw end is designed to give maximum penetration into packing. Flexible Packing Extractors are supplied individually or in boxed kits of all four sizes. The Packing Extractors with the renewable tips come complete with two new tips. Individual spare tips may be purchased as required

Technical Data Sheet >


 

AA 500- Super Slide Injection Gun The injection gun utilizes a button-head or flow-through fitting permanently installed on the pump or valve stuffing box. Since it requires no electricity, the injection gun can be used anywhere to replenish sealant easily and conveniently. The all-steel hydraulic gun is completely portable and is very easy to use. The valve or pump stuffing box fitting allows the sealant to be hand-injected into the shaft stuffing box using the injector gun. No downtime is required for the repacking operation since the equipment can continue to run during the repacking operation. The BJSEAL AA-500 Hydraulic Hand Gun features a unique locking handle to prevent pump piston damage. Hydraulic pressure is generated by stroking the handle. The cleaner or lubricant / sealant is discharged at up to 10,000 psi. Discharges 1 oz. of product easily with each 50 strokes.

  • Generates up to 10,000 psi (750 Bar)when required.
  • Light weight, very portable.
  • Can also pump liquids, flange sealants and stem packing’s.
  • Self-priming hydraulic action makes manual injection simple.

Available sizes
AA 500- Injection Gun Hand Operated 750 Bar
AA 500P-Injection gun Pneumatically Operated 750 Bar(Foot Pump Operated Trigger & Hoses)

Back to top >


AA 600 Packing Cutter will save time, money and braided packing while providing precision skive and butt cuts for the highest quality packing installations .Bjseal Cut Packing Cutter will cut a number of different packing’s. Perfect 45 degree (Skive) or 90 degree (Butt) cuts are accomplished by changing the guide fence position. Just push up on the fence retainer button on the underside of the table and turn the fence until alignment pins in the fence line up with alignment holes in table. Perfect 45 degree (Skive) or 90 degree (Butt) cuts are accomplished by changing the guide fence position. Just push up on the fence retainer button on the underside of the table and turn the fence until alignment pins in the fence line up with alignment holes in table.

The Packing cutter cuts Teflon, Cotton yarn, GFO yarn, Acrylic Rayon Fiberglass yarn, Lead  Foil packing, Inconel wire carbon yarn packing; will cut some Kevlar/composite packing; not designed to cut pure Kevlar. Packing cutter has also been used to cut large o-ring material, Felt & rubber seal strip materials

Back to top >


AA-625 Gland Packing Cutter. AA625 Packing Cutter will save time, money and braided packing while providing precision skive and butt cuts for the highest quality packing installations. AA 625 Cut Packing Cutter will cut a number of different packing’s. Perfect 45 degree cuts are accomplished by changing the guide fence position. Just push up on the fence retainer button on the underside of the table and turn the fence until alignment pins in the fence line up with alignment holes in table. Perfect 45 degree (Skive) cuts are accomplished by changing the guide fence position. Just push up on the fence retainer button on the underside of the table and turn the fence until alignment pins in the fence line up with alignment holes in table,robust and accurate cutting jig that simplifies the production of perfectly matching 45° scarf joints on packing.

The Packing cutter cuts Teflon, Cotton yarn, GFO yarn, Acrylic Rayon Fiberglass yarn, Lead Foil packing, Inconel wire carbon yarn packing; will cut some Kevlar/composite packing; not designed to cut pure Kevlar. Packing cutter has also been used to cut large o-ring material, Felt & rubber seal strip materials.Packing Cutter AA625 Size Packing Ring Cutter 4"(1" max. packing size - 4"max. shaft size) and 10"(1" max. packing size - 10" max. shaft size).Just match the section of the packing to the ring inside diameter required, then simply cut the exact ring length required with perfect scarf joints.

Available sizes

BJ-AA625 Gland Packing Cutter Packing Size 1” Shaft Size Max. 4”
BJ-AA625A Gland Packing Cutter Packing Size 1” Shaft Size Max. 10”

Back to top >


AA 650 Water Jetting Packing Extractor-Air Operated.The model AA 650 water, jet packing extraction, system consists of an air operated, high pressure pumping system, high pressure hose, extraction gun, portable reservoir, and nozzle kit. This system has been designed for fast and efficient removal of valve stem packing, pump packing and flange gasketing. It also eliminates the risk of scoring or gouging a valve stem, stuffing box bore, or flange face cause by out-dated manual extraction methods. The AA 600 system allows for instantaneous flow control at the gun without the use of any electrical or pneumatic remote controls or switches. The Extraction gun is a hand held device that is activated by depressing a gun type trigger. This allows for a safe and positive flow shut-off control at the gun.  Releasing the gun trigger stops all jetting flow instantaneously, regardless of the distance from the pumping unit. When the trigger is released, the pump unit will stall at the preset operating pressure. The AA 650 provides the operator with the ultimate in safety and positive control of the amount of water or chemical used in the extraction process

Features

  • All controls located on control panel, behind lockable ventilated door.
  • Discharge pressure to 20,000 PSIG-(138MPa)(1400BAR)
  • No electrical components for safe, non sparking operation.
  • Operates using plant water via hose or non pressurized portable reservoir.
  • Stainless steel console, corrosion resistant, with rear panel removal, drawer like entry with no piping to disconnect.
  • Sample case size, light weight, for operating in tight spaces and elevated areas.
  • Reduce labor cost/1man operation
  • Plant air operated system
  • High pressure relief valve
  • Water inlet filter, auto drain air filter.

Specifications

  • Size: 11"High x 20" wide x 17" deep  (28cm x 51cm x 43cm)
  • Weight: 87 pounds(40kg)
  • Air Requirements: 70 to 100psi @ 50cfm
  • Gun: 20,000 PSI-WP
  • Hose: 26,000 PSI-WP, 60,000 PSI
  • Burst, 1\2" O.P.

Back to top >


Allpax Standard Extension-Style Gasket Cutter Kits Now you can accurately cut your own gaskets quickly and efficiently to reduce costly downtime. Allpax Extension Gasket Cutters are available in five convenient sizes to meet a broad range of cutting requirements.   All kits come packed in a durable metal storage box for protection and convenience. Each kit contains all that is needed to cut your required gaskets quickly and accurately to size.Each Kit Contains:  Cutter block, cutter head screws, regular gasket cutter blades, heavy duty cutter blades, pivot post, knurled nuts, centre pins, extension bars, suitable cutting board, piercing tool and necessary ancillary tools.

Extension gasket cutter kits - Inch

Item no

Gasket Sizes

100K13-Kit No 1

Gasket Cutter Kit Complete Cuts ¼” to 13”

100K25-Kit No 2

Gasket Cutter Kit Complete Cuts ¼” to 25”

100K37-Kit No 3

Gasket Cutter Kit Complete Cuts ¼” to 37”

100K49-Kit No 4

Gasket Cutter Kit Complete Cuts ¼” to 49”

100K61-Kit No 5

Gasket Cutter Kit Complete Cuts ¼” to 61”

100U13-Kit no 6

Gasket Cutter Kit W/OCutting Board Cuts 1/4"to 13"

Extension gasket cutter kits - Metric

Item no

Gasket Sizes

100KM330 - Kit No-1

Gasket Cutter Kit Complete Cuts 6mm to 330mm

100KM635 - Kit No-2

Gasket Cutter Kit Complete Cuts 6mm to 635mm

100KM940 - Kit No-3

Gasket Cutter Kit Complete Cuts 6mm to 940mm

100KM1245-Kit No-4

Gasket Cutter Kit Complete Cuts 6mm to 1245mm

100KM1550-Kit No-5

Gasket Cutter Kit Complete Cuts 6mm to 1550mm

-100UM330-Kit  No-6

Gasket Cutter Kit w/o Cutting Board 6mm to 30mm

Back to top >


Allen M3 Rotary-Style Gasket Cutter (Vise Mounted)Cut accurate flange and ring gaskets with the Allen M3 Rotary-Style Gasket Cutter. Designed primarily for non-metallic gasket materials such as cork, fiber, and rubber, up to ¼” thick. Cuts gaskets with a face width of ¼” to 7”; from 2” ID to 22” OD. Accessory scale bars (not included) extend cutting range from 22” ID to 42” OD, or 42” ID to 62” OD. Mounts on a vise, or clamps to a piece of angle iron.

Technical Data Sheet >


Allen SM4 Rotary-Style Gasket Cutter (Bench Mounted)Cut accurate flange and ring gaskets with the heavy-duty, Allen SM4 Rotary-Style Gasket Cutter. Primarily designed for metallic gasket materials such as soft steel, copper, zinc, and brass. Also cuts non-metallic materials such as hard fiber, rubber, and Teflon. Cuts gaskets with a face width of .5" to 8.75"; from 3" ID to 28” OD. Accessory scale bars (not included) extend cutting range from 28" ID to 54” OD, or 54" ID to 80" OD.

Technical Data Sheet >


 

 

Standard Hollow Punch Tool Kits Quickly and easily cut precision bolt holes in flange gaskets. Select the desired diameter cutting head, mount handle, position on gasket material, and strike! Patented locking system allows rapid interchange of cutting heads. Unique design performs single diameter (hole) cuts as well as dual diameter (ring) cuts in one operation. Hardened steel cutting heads stay sharp.

Hole punch kits-Inch

Item no

 

Punch sizes

100K11

11 Piece Standard Hollow Punch Tool Kit 10 Punch Sizes:1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4"

100K16

16 Piece Standard Hollow Punch Tool Kit 15 Punch Sizes:1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8, 1", 1-1/16", 1 - 1/8", 1 - 3/16"

100K27

27 Piece Standard Hollow Punch Tool Kit 25 Punch Sizes:1/8",3/16",1/4",5/16",3/8",7/16",1/2",9/16",5/8",3/4",7/8,1",1-1/16",1-1/8",1-3/16",1-1/4,1-5/16,1-3/8",1-7/16",1-1/2",1-5/8",1-11/16",1-3/4"1-7/8", 2"

Hole punch kits-Metric


Item no

Punch sizes

100KM11

11 Piece Hollow Punch Tool Kit- 10 PUNCH- SIZES: 3mm,4mm,6mm,8mm,10mm,12mm,14mm,16mm 18mm,20mm

100KM16

16 Piece Hollow Punch Tool Kit-15 PUNCH-SIZES:3mm,4mm,6mm,8mm,10mm,12mm,14mm,16mm,18mm,20mm, 22mm, 24mm, 26mm, 28mm, 30mm

100KM31

31 Piece Hollow Punch Tool Kit 29 PUNCH -SIZES:2mm,3mm,4mm,5mm,6mm,7mm, 8mm,9mm,10mm,12mm,14mm,16mm,18mm,20mm,22mm,24mm,26mm,28mm, 30mm, 32mm, 34mm, 36mm, 38mm, 40mm, 42mm, 44mm, 46mm, 48mm, 50mm


AA 900-PTFE-Flexible Lantern Ring Material
AA900 Made of 100% PTFE material, Flexible Lantern Material is an innovative approach to standard lantern rings. Designed to perform like lantern rings, Flexible Lantern Material is easier to install and remove. Sold in roll form like bulk packing, Flexible Lantern Ring Material can be cut to the specific length needed, therefore eliminating the need to stock many different size rings. The Lantern Ring is simple to use. Just uncoil the length, wrap it around the pump shaft and butt cut to size. Ring will spring to the bore of the stuffing box, providing shaft clearance. For perfect end joint fit, wrap two turns of electrical tape around a mandrel of the same size as pump shaft and butt cut. Size Selection: Choose the same size as the packing cross section and choose the width which match

Cross Section

Width

Length in Meter

1/4"

3/8"

1.2

5/16"

7/16"

1.2

7/16"

9/16"

1.2

1/2"

5/8"

1.2

9/16"

11/16"

1.2

5/8"

3/4"

1.2

3/4"

7/8"

1.2

7/8"

1"

1.2

1"

1"

1.2


 

 

 

 

*All sizes 1.4 meter length